SanDisk Cruzer Blade pada Ubuntu 16.04

1

Saya memiliki USB stick 128G tetapi Ubuntu tidak memasangnya, tidak melihat partisi dan tidak membiarkan saya memformatnya.

dmesg:

[ 3124.001070] scsi host8: usb-storage 3-6:1.0
[ 3125.001042] scsi 8:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.27 PQ: 0 ANSI: 6
[ 3125.001511] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 3125.002864] sd 8:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[ 3125.004512] sd 8:0:0:0: [sdb] Write Protect is off
[ 3125.004516] sd 8:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3125.004788] sd 8:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3155.886694] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3186.917281] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3217.963891] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3248.930474] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3259.170022] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3275.409403] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3275.649387] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3285.888788] usb 3-6: reset high-speed USB device number 9 using xhci_hcd
[ 3286.017438] sd 8:0:0:0: Device offlined - not ready after error recovery
[ 3286.017447] sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[ 3286.017450] sd 8:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[ 3286.017452] blk_update_request: I/O error, dev sdb, sector 0
[ 3286.017455] Buffer I/O error on dev sdb, logical block 0, async page read
[ 3286.017491] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017499] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017502] ldm_validate_partition_table(): Disk read failed.
[ 3286.017505] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017509] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017512] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017516] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017518] Dev sdb: unable to read RDB block 0
[ 3286.017521] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017525] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017533] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017537] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017540] sd 8:0:0:0: rejecting I/O to offline device
[ 3286.017542]  sdb: unable to read partition table
[ 3286.017654] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[ 3507.045052] usb 3-6: USB disconnect, device number 9
[ 3532.849931] usb 3-6: new high-speed USB device number 10 using xhci_hcd
[ 3534.530519] usb 3-6: New USB device found, idVendor=0781, idProduct=5567
[ 3534.530525] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3534.530528] usb 3-6: Product: Cruzer Blade
[ 3534.530530] usb 3-6: Manufacturer: SanDisk
[ 3534.530532] usb 3-6: SerialNumber: 4C530000360119115540
[ 3534.531122] usb-storage 3-6:1.0: USB Mass Storage device detected
[ 3534.532419] scsi host9: usb-storage 3-6:1.0
[ 3535.530816] scsi 9:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.27 PQ: 0 ANSI: 6
[ 3535.531338] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 3535.532651] sd 9:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[ 3535.534275] sd 9:0:0:0: [sdb] Write Protect is off
[ 3535.534282] sd 9:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3535.534600] sd 9:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA

dmesg pada port USB2:

[13712.795990] usb 3-6: new high-speed USB device number 16 using xhci_hcd
[13714.424628] usb 3-6: New USB device found, idVendor=0781, idProduct=5567
[13714.424632] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[13714.424634] usb 3-6: Product: Cruzer Blade
[13714.424636] usb 3-6: Manufacturer: SanDisk
[13714.424637] usb 3-6: SerialNumber: 4C530000360119115540
[13714.425386] usb-storage 3-6:1.0: USB Mass Storage device detected
[13714.425523] scsi host10: usb-storage 3-6:1.0
[13715.425303] scsi 10:0:0:0: Direct-Access     SanDisk  Cruzer Blade     1.27 PQ: 0 ANSI: 6
[13715.425690] sd 10:0:0:0: Attached scsi generic sg2 type 0
[13715.427008] sd 10:0:0:0: [sdb] 250085376 512-byte logical blocks: (128 GB/119 GiB)
[13715.428665] sd 10:0:0:0: [sdb] Write Protect is off
[13715.428668] sd 10:0:0:0: [sdb] Mode Sense: 43 00 00 00
[13715.428953] sd 10:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[13746.221203] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13777.190106] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13808.175044] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13839.208027] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13849.452206] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13865.692838] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13865.988708] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13876.229026] usb 3-6: reset high-speed USB device number 16 using xhci_hcd
[13876.357892] sd 10:0:0:0: Device offlined - not ready after error recovery
[13876.357912] sd 10:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[13876.357919] sd 10:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[13876.357924] blk_update_request: I/O error, dev sdb, sector 0
[13876.357931] Buffer I/O error on dev sdb, logical block 0, async page read
[13876.358015] sd 10:0:0:0: rejecting I/O to offline device
[13876.358042] sd 10:0:0:0: rejecting I/O to offline device
[13876.358049] ldm_validate_partition_table(): Disk read failed.
[13876.358059] sd 10:0:0:0: rejecting I/O to offline device
[13876.358069] sd 10:0:0:0: rejecting I/O to offline device
[13876.358080] sd 10:0:0:0: rejecting I/O to offline device
[13876.358090] sd 10:0:0:0: rejecting I/O to offline device
[13876.358097] Dev sdb: unable to read RDB block 0
[13876.358105] sd 10:0:0:0: rejecting I/O to offline device
[13876.358116] sd 10:0:0:0: rejecting I/O to offline device
[13876.358136] sd 10:0:0:0: rejecting I/O to offline device
[13876.358147] sd 10:0:0:0: rejecting I/O to offline device
[13876.358158] sd 10:0:0:0: rejecting I/O to offline device
[13876.358163]  sdb: unable to read partition table
[13876.358568] sd 10:0:0:0: [sdb] Attached SCSI removable disk

fsck:

sela@sela-ThinkPad-T440p:~$ sudo fsck -n /dev/sd
/dev/sda   /dev/sda1  /dev/sda2  /dev/sda5  /dev/sdb 
sela@sela-ThinkPad-T440p:~$ sudo fsck -n /dev/sdb
fsck from util-linux 2.27.1
e2fsck 1.42.13 (17-May-2015)
fsck.ext2: No such device or address while trying to open /dev/sdb
Possibly non-existent or swap device?

lsusb:

sela@sela-ThinkPad-T440p:~$ lsusb
Bus 002 Device 002: ID 8087:8000 Intel Corp. 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 138a:0017 Validity Sensors, Inc. Fingerprint Reader
Bus 003 Device 010: ID 0781:5567 SanDisk Corp. Cruzer Blade
Bus 003 Device 002: ID 058f:9540 Alcor Micro Corp. AU9540 Smartcard Reader
Bus 003 Device 006: ID 04f2:b39a Chicony Electronics Co., Ltd 
Bus 003 Device 004: ID 0bdb:193e Ericsson Business Mobile Networks BV 
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Tetap mencoba memformat:

sela@sela-ThinkPad-T440p:~$ sudo mkfs.fat /dev/sdb -I
mkfs.fat 3.0.28 (2015-05-16)
/dev/sdb: No such device or address

Tidak dapat menemukan solusi. Bantuan apa pun akan dihargai.

Sunting: Di aplikasi Disk saya menemukan ini:

masukkan deskripsi gambar di sini

Hal lain yang saya coba:

sela@sela-ThinkPad-T440p:~$ sudo tune2fs -l /dev/sdb 
tune2fs 1.42.13 (17-May-2015)
tune2fs: No such device or address while trying to open /dev/sdb
Couldn't find valid filesystem superblock.

Hal lain yang saya coba adalah mengubah keadaan perangkat dan memformatnya:

sela@sela-ThinkPad-T440p:~$ sudo -s
root@sela-ThinkPad-T440p:~# cat /sys/bus/scsi/devices/7\:0\:0\:0/state 
offline
root@sela-ThinkPad-T440p:~# echo running > /sys/bus/scsi/devices/7\:0\:0\:0/state 
root@sela-ThinkPad-T440p:~# cat /sys/bus/scsi/devices/7\:0\:0\:0/state 
running
root@sela-ThinkPad-T440p:~# mkdosfs -v -n 'SELA111' -I /dev/sdb 
sdb
root@sela-ThinkPad-T440p:~# mkdosfs -v -n 'SELA111' -I /dev/sdb  
mkfs.fat 3.0.28 (2015-05-16)
/dev/sdb: No medium found
root@sela-ThinkPad-T440p:~#

Apakah jejak tumpukan ini terkait?

[ 6478.677549] usb 3-6: reset high-speed USB device number 15 using xhci_hcd
[ 6480.129365] INFO: task kworker/u16:4:4979 blocked for more than 120 seconds.
[ 6480.129369]       Not tainted 4.4.0-24-generic #43-Ubuntu
[ 6480.129370] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 6480.129372] kworker/u16:4   D ffff8804033a3848     0  4979      2 0x00000000
[ 6480.129380] Workqueue: events_unbound async_run_entry_fn
[ 6480.129381]  ffff8804033a3848 ffff8804261f6a80 ffff88042c2d5280 ffff880425003700
[ 6480.129383]  ffff8804033a4000 ffff88043e396d00 7fffffffffffffff ffffffff81822310
[ 6480.129385]  ffff8804033a39a8 ffff8804033a3860 ffffffff81821b15 0000000000000000
[ 6480.129387] Call Trace:
[ 6480.129392]  [<ffffffff81822310>] ? bit_wait+0x60/0x60
[ 6480.129395]  [<ffffffff81821b15>] schedule+0x35/0x80
[ 6480.129397]  [<ffffffff81824c35>] schedule_timeout+0x1b5/0x270
[ 6480.129401]  [<ffffffff813bb526>] ? submit_bio+0x76/0x170
[ 6480.129403]  [<ffffffff81822310>] ? bit_wait+0x60/0x60
[ 6480.129405]  [<ffffffff81821044>] io_schedule_timeout+0xa4/0x110
[ 6480.129407]  [<ffffffff8182232b>] bit_wait_io+0x1b/0x70
[ 6480.129409]  [<ffffffff81821ebd>] __wait_on_bit+0x5d/0x90
[ 6480.129413]  [<ffffffff812481d0>] ? blkdev_readpages+0x20/0x20
[ 6480.129416]  [<ffffffff8118cd0b>] wait_on_page_bit+0xcb/0xf0
[ 6480.129421]  [<ffffffff810c3bc0>] ? autoremove_wake_function+0x40/0x40
[ 6480.129423]  [<ffffffff8118cf39>] wait_on_page_read+0x49/0x50
[ 6480.129426]  [<ffffffff8118e56d>] do_read_cache_page+0x8d/0x1b0
[ 6480.129428]  [<ffffffff8118e6a9>] read_cache_page+0x19/0x20
[ 6480.129430]  [<ffffffff813ce77d>] read_dev_sector+0x2d/0x90
[ 6480.129433]  [<ffffffff813d51fd>] read_lba+0x14d/0x210
[ 6480.129435]  [<ffffffff813d5ab2>] efi_partition+0xf2/0x7d0
[ 6480.129438]  [<ffffffff813f4ffb>] ? string.isra.4+0x3b/0xd0
[ 6480.129440]  [<ffffffff813f6f39>] ? snprintf+0x49/0x60
[ 6480.129442]  [<ffffffff813d59c0>] ? compare_gpts+0x280/0x280
[ 6480.129443]  [<ffffffff813cfb2e>] check_partition+0x13e/0x220
[ 6480.129445]  [<ffffffff813cf060>] rescan_partitions+0xc0/0x2b0
[ 6480.129447]  [<ffffffff812490cd>] __blkdev_get+0x30d/0x460
[ 6480.129449]  [<ffffffff8124968d>] blkdev_get+0x12d/0x340
[ 6480.129453]  [<ffffffff812274f9>] ? unlock_new_inode+0x49/0x80
[ 6480.129455]  [<ffffffff81248068>] ? bdget+0x118/0x130
[ 6480.129459]  [<ffffffff813ccb13>] add_disk+0x403/0x490
[ 6480.129463]  [<ffffffff815592a1>] ? update_autosuspend+0x51/0x60
[ 6480.129465]  [<ffffffff8155936c>] ? __pm_runtime_use_autosuspend+0x5c/0x80
[ 6480.129469]  [<ffffffff815c0845>] sd_probe_async+0x115/0x1d0
[ 6480.129471]  [<ffffffff810a30a8>] async_run_entry_fn+0x48/0x150
[ 6480.129474]  [<ffffffff8109a175>] process_one_work+0x165/0x480
[ 6480.129476]  [<ffffffff8109a4db>] worker_thread+0x4b/0x4c0
[ 6480.129477]  [<ffffffff8109a490>] ? process_one_work+0x480/0x480
[ 6480.129479]  [<ffffffff8109a490>] ? process_one_work+0x480/0x480
[ 6480.129481]  [<ffffffff810a06a8>] kthread+0xd8/0xf0
[ 6480.129483]  [<ffffffff810a05d0>] ? kthread_create_on_node+0x1e0/0x1e0
[ 6480.129484]  [<ffffffff81825f8f>] ret_from_fork+0x3f/0x70
[ 6480.129486]  [<ffffffff810a05d0>] ? kthread_create_on_node+0x1e0/0x1e0
[ 6488.917955] usb 3-6: reset high-speed USB device number 15 using xhci_hcd
partitioning  mount  16.04  usb-storage 
— selalerer
sumber
1
@Sneetsher Dikatakan "baru berkecepatan tinggi ..." di mana pun saya menghubungkannya. Di port dengan ss dan yang tanpa itu.
— selalerer

Jawaban:

2

Untuk beberapa alasan, perangkat ini tiba-tiba dihapus oleh kernel atau pengontrol USB dengan cara yang tidak bersih, sehingga meninggalkan /devsimpul - simpul tersebut.

Ini adalah perangkat USB2!

Seperti yang saya lihat data spesifikasi SanDisk Cruzer Blade .:

Capacity    128 GB   64 GB    32 GB    16 GB    8 GB     4 GB
Generation  USB 2.0  USB 2.0  USB 2.0  USB 2.0  USB 2.0  USB 2.0

Seharusnya perangkat USB2. Jadi bisa bermasalah dengan port USB3

usb 3-6: reset high-speed USB device number 9 using xhci_hcd
...
usb 3-6: new high-speed USB device number 10 using xhci_hcd

Ubah ke port USB2 lain laptop Anda seharusnya sudah memiliki 2 port ( Lenovo ThinkPad T440p spec. ).

Jelas yang xhci_hcdterdeteksi sebagai perangkat USB2 dari deskripsinya

usb 3-6: perangkat USB berkecepatan tinggi baru nomor 10 menggunakan xhci_hcd

Perangkat USB3 harus mendapatkan super-speedatau super-speed+. Referensi: Wikipedia: USB, Riwayat Versi

Opsi 1. Nonaktifkan USB3 dari BIOS

Ini menyebutkan manual :

  • 2 sisi kiri, seperti USB3
  • 2 sisi kanan, seperti USB (? Jika ada +tanda itu adalah USB2)

  • BIOS memiliki opsi untuk menonaktifkan USB3 pada 2 port bersama antara USB2 & USB3. Sisi mana? Saya tidak tahu!

    Jadi mungkin port bersama adalah yang ada di sisi kanan. Nonaktifkan USB3 dari BIOS dan lihat apa output baru dmesgdi kedua sisi, ditambah output dari lsusb.

Opsi 2. Tingkatkan BIOS / UEFI

Ada rilis baru:

Ukuran Utilitas Pembaruan BIOS: 5,7 MB 2,37 4/28/2016

Catatan rilis menyebutkan masalah USB terhitung, yang paling menarik adalah ini:

<2.19>  UEFI: 2.19 / ECP: 1.08
- (Fix) Fixed an issue that might fail to boot the computer remotely.
- (Fix) Fixed an issue where USB 3.0 device detection might fail when the device
        was attached via the USB 3.0 Hub and the USB 3.0 Mode option was set to
        Enabled in ThinkPad Setup.
— user.dz
sumber
1
Apakah port tanpa port USB2 ss? Jika demikian, itu tidak membantu menghubungkan tongkat di sana. Berperilaku persis sama.
— selalerer
Saya menambahkannya. Ini setelah menunggu sekitar 30 detik. Saya akan tetap terhubung dan melihat apakah ada sesuatu yang baru muncul dalam beberapa menit.
— selalerer
Sekarang saya melihatnya. Saya pikir yang pertama juga di port yang sama.
— selalerer
@selalerer ya itu dan itu adalah USB3, masih !!!
— user.dz
1
tapi ini adalah salah satu port di sisi kanan laptop yang tidak memiliki tanda ss.
— selalerer
Dengan menggunakan situs kami, Anda mengakui telah membaca dan memahami Kebijakan Cookie dan Kebijakan Privasi kami.
Licensed under cc by-sa 3.0 with attribution required.